BASIC INSTRUCTIONS
SANI-TRED Products And Their Containers:
1. LRB (LIQUID RUBBER BASE): 5 gallon pail and 1 gallon pail with blue label, or 1 quart can, and 1/2 pint can marked LRB
2. LRB Catalyst: 2 oz LRB Catalyst per 5 gal pail of LRB and .4 oz LRB Catalyst per 1 gal pail of LRB when not using TAV
3. T.A.V. (THICKENING ACTIVATOR): 5 gallon pail, 1 gallon pails, 1 qt. can, 1 pint can) No LRB Catalyst needed when mixing LRB with TAV
4. PERMAFLEX: 5 gallon pail and 1 gallon pail come with green label, or 1 quart can and 1/2 pint can marked PermaFlex
6. PERMAFLEX Catalyst for 5 gal. pails: 1/2 pint can marked PERMAFLEX Catalyst
7. PERMAFLEX Accelerator for 5 gal. pails: 1 quart can marked PERMAFLEX Accelerator
8. PERMAFLEX Catalyst and Accelerator for 1 gal. pails: 8oz. bottle labeled "PERMAFLEX ACCELERATOR and CATALYST"
9. PERMAFLEX Catalyst and Accelerator for 1 qt. can: 2 oz. bottle labeled "PERMAFLEX ACCELERATOR and CATALYST"
10. PERMAFLEX-AL: 5 gallon pail, 1 gallon pail with salmon or gold colored label, or 1 qt., 1/2 pint can marked PERMAFLEX-AL. PermaFlex-AL is an extreme UV resistant outdoor topcoat. NO PERMAFLEX CATALYST IS REQUIRED WITH PERMAFLEX-AL, ONLY PERMAFLEX ACCELERATOR at the same rate as added to PERMAFLEX.
11. TAV- Plus: 5 gallon pails, 1 gallon pails, 1 qt. can, 1 pint can, and 1/2 pint can. No LRB Catalyst needed when mixing LRB with TAV-Plus. TAV-Plus is mixed 50-50 with LRB or 1 part LRB with 1 part (or less) TAV-Plus...
PERMAFLEX: Basic how - to
1 Open the lid of the plastic container of Permaflex. Also the catalyst / accelerator which is supplied with the container, and the xylene reducer. A good 2 pack acrylic thinner can be used if xylene is not available.
2 Mix the Permaflex very well using a very strong but slow power paddle, before adding the other ingredients...
Preparation and Application of Sani-Tred products to Fibre Glass boats and Yachts
* Once removed from the water, the boat has to be carefully washed with plenty of clean water.
* Remove any algae and marine life, which has attached itself to the hull, using a pressure washer and a plastic scraper.
* Allow to dry, Grit blast with fine grade grit 180 to achieve a 75-micron profile and to remove all previous coatings on the Fibre Glass...
Preparation and Application of Sani-Tred products to Mild Steel shipping vessel Boyars
* Remove from water and wash with a pressure washer and metal scrapers to remove all marine life which has attached themselves to the Boyar.
* Grit blast to remove all previous coatings and to achieve SA2.5 at 75-micron profile to the Mild Steel...
Rates of use
All you need to know on rates of use for Sani - Tred products. Tabelar view...
Recognized preparation and application procedures for Sani-Tred products to wooden surfaces
The most important first step for the preparation to the wooden surface is to completely remove all previous coatings, revealing the bare wood. This also entails removal of any puttys, filler and so forth.
The removal of previous coatings can be carried out by...
Recognized preparation on concrete
The recognized preparation and application of Sanitred's Permaflex and LRB/TAV on Concrete are as follows: * To remove the entire thin layer of lime scale, which is formed, in the curing process of freshly, poured concrete by either: - Sweep p180 grade Grit Blasting.
- Pressure Water Blasting with 3,000 psi.
- Acid Etching
Just enough to reveal the pores of the concrete surface...
Recognized preparation on steel
The recognized preparation and application of Sanitreds Permaflex and LRB/TAV on steel are as follows:
* To wash the whole area to be coated with a mild soapy solution and rinse with plenty of fresh clean water, degrease the whole area and allow to fully dry.
* Grind down any arch welding splatter and round off any sharp edges...
| 
Applications
